Product Overview
The ANENG M469A is a professional multi-function cable tester and line finder designed for network technicians, electricians, and DIY installers. It combines network route searching, cable proofreading, DC level testing, power cable routing, telephone line search, open/short circuit testing, and earphone cable testing in one rugged device. Featuring RJ11 and RJ45 interfaces, a built-in flashlight, and a metal probe, it makes cable identification fast and reliable. Key Features at a Glance
Network Route Searching locate cables quickly and accurately
Network Cable Proofreading verify line sequence and detect faults
DC Level Test identify positive and negative poles
Power Cable Routing trace live electrical cables
Telephone Line Search RJ11 compatibility
Open Circuit / Short Circuit Test diagnose cable faults
Earphone Cable Testing comes with headset cable support
Double Speed Switching fast/slow mode selection
Flashlight Lighting for dark working environments
Single/Dual Audio Switching flexible audio testing
Volume Adjustable via rotary knob
Automatic Shutdown power saving function RJ11/RJ45 Compatibility
Applicable to RJ45 network cable interfaces and RJ11 telephone interfaces simple operation for both.
If it is a shielded network cable, the G light is on after 18 indicator lights How to Use
1. Telephone Line Search Function
Plug the telephone line with a crystal head into the transmitter interface RJ11
Turn the function selection of the transmitter to the line finding position the line finding indicator light flashes, indicating the transmitter works normally
2. Network Line Search Function
Plug the network cable with crystal head into the transmitter interface RJ45
Turn the function selection of the transmitter to the line finding position the line finding indicator light flashes, indicating the transmitter works normally
3. Power Cable Line Searching Function
Connect the transmitter and the metal wire to be tested with the alligator clip, and insert one end into the transmitter
Turn the function selection switch of the transmitter to the line finding position the line finding indicator light flashes, indicating the transmitter works normally
4. Network Cable Proofreading
Insert RJ45 connectors at both ends of the network cable to be tested into the corresponding interfaces of the transmitter and receiver
Turn the function selection switch of the transmitter to the alignment position the line sequence light flashes, indicating the transmitter works normally
According to the 18 line sequence lamps, judge the characteristics of short circuit, open circuit, and cross
5. DC Level Positive/Negative Pole Test
Turn the function to line finding, press and hold switch for more than 2 seconds until the line finding light goes out
The line sequence light flashes
If the scan light is red, the red alligator clip is holding the positive pole
If the scan light is green, the red alligator clip is holding the negative pole
The brighter the light, the higher the level the darker the light, the lower the level
6. Open Circuit Short Circuit Test Function
Turn the function to line alignment, and press and hold the switch button for more than 2 seconds until the line sequence light changes from flashing to constant light
Insert the alligator clip into the RJ11 socket, and the alligator clip clamps both ends of the line
If there is a short circuit, the transmitters scanning red light will be on
The brighter the lamp, the smaller the impedance the darker the lamp, the greater the impedance
7. Earphone Cable Clearly Listens
In a noisy environment, you can wear the earphone cable to operate, and adjust the volume through the knob. Function Analysis
Transmitter (Master)
RJ11 socket
RJ45 socket
Line finding indicator
Function switch
Function selection (Upper: alignment / Medium: shutdown / Lower: search line)
Linear sequence lamp
Shielded wire lamp
Line detection lamp
Receiver (Remote)
Metal probe
Floodlight
Seeking signal lamp
Headphone jack
Volume adjustment knob
Lamp switch
Seek button
Linear sequence lamp
RJ45 socket Specifications
Accuracy Class: 1%
Application: Car battery recharge test repair
Support Battery: 12V lead acid batteries (6F22 9V for tester)
Voltage Range: 816V
Input Resistance: 1 mΩ 30 Ω
Maximum Measuring Voltage: 816V
Measuring Resistance Range: 1 mΩ 30 Ω
Type: Digital Battery Tester / Cable Tester
Place of Origin: China In the Box
ANENG M469A Transmitter (Master) 1
ANENG M469A Receiver (Remote) 1
Alligator Clip Cable 1
Earphone Cable 1
9V Battery 1
User Manual 1
Carrying Bag 1
